Posts

Showing posts with the label velie monocoupe

Completion

Image
  AUW 680gr / 24oz and Wing cube loading ~8.30 Drive setup: DYS D2830-1300Kv (275W max rated), 3S Lipo 2,200mAh, 20A ESC, 8x6 prop Radio equipment: FlySky 8ch receiver, Radiomaster TX16X transmitter

Electronics

Image
The fuselage cabin area is rather cavernous and installing modern radio electronics does not pose any difficulties. Care should be taken to position the components in a way that allows easy access and also aide in balancing. This picture shows the elevator and rudder servos with the receiver and antenna positions: The heavier components such as ESC and battery are positioned as forward as possible under the turtle deck through the hollowed F1 and up against the firewall:

Covering the wing

Image
Covering the wing required two steps. First I covered the bottom of both panels, and before covering to tops I installed the aileron servos and ran the wires to the wing center: Since the servos are covered and have no access hatch, I installed a 1/8" square between the aileron servo ribs. This way, when the wing is completely covered only a small patch can be removed and reattached above the servo. The 1/8" stick, ribs and top spar form a convenient surface for adhesion. The finished wing, covered and with two coats of sealer before attaching the ailerons.

Dummy 5-cylinder engine

Image
The motor I am using for the Velie Monocoupe is a DYS D2830 brushless motor that will drive an 8x6 propeller and powered by a 3S Lipo. The real Monocoupe is powered by a 5-cylinder radial engine and many models use some type of dummy engine made of balsa or other material. I decided to try a 3D printed engine model combined with a simple cowl. The 3D design is posted and available for download on GrabCAD: https://grabcad.com/library/velie-monocoupe-rc-model-5-cylinder-engine-dummy-1   The hot end on the printer was probably set a few degrees too high for this new spool of PLA and I had some stringing and distortion on the thin edges. After some light sanding and a coat of black spray paint it looks ok, although I might end up reprinting it.

Wheels and landing gear

Image
I used 3" Dubro spoke wheels. Although not exactly scale size I chose them because I typically fly off of a grass field. These wheels are thin and light, and may later be useful if I want to convert them to wired spokes. I decided to cover them with orange tissue so I first removed the foam and glued balsa to form a surface. I then covered the balsa with orange tissue and reassembled the foam rim: The landing gear is a simple wire frame with the wheel axis held in place by silicone rubber bands that I sliced off of a rubber tube:

Covering

Image
I selected Esaki tissue from Peck Polymers; picked blue and orange that best fit the end result I wanted to achieve: colors that are close to the actual plane and a covering material that will highlight the model's structure. These are the horizontal stabilizer and elevator fins covered in orange tissue with two coats of sealer: After practicing on the stabilizers, elevator, and rudder I turned my attention to the fuselage. The complex contours posed a challenge that I wanted to tackle first and here are some results. The windows are covered and cut away after applying a coat of sealer to the covering, leaving the cross members covered: A view of the internal setup and a top view of the battery hatch: The battery hatch is located at the bottom of the fuselage behind F3. The hatch is secured with a simple swiveling latch and a silk strap:  

Wing struts

Image
 Struts are made according to the plans with bamboo skewers and 1/8"x1/2" trailing edge: With the wing braced to the fuselage and verified to be square and level I glued the struts together per plans. The front and back struts are glued with epoxy: The connectors as the strut tips are small automotive cable connectors. The blue will match the covering color of the fuselage, one end matched the skewer diameter, and the other end has a metal loop that exactly matched the #4-40 screws I used to secure the struts: A view of the finished and sanded struts connecting wing and fuselage. The #4-40 nylon screws fit into blind nuts embedded into the side of the fuselage and into gussets under the wing:

Completing the wing

Image
The wing has no dihedral so attaching the two panels was relatively straight forward. I cut a dihedral brace from 1/16" light plywood and fit it into a slot cut into the main spars. The slot runs through the first bay and the brace then fits between the spars in the second bay: The completed wing with both panels glued into one: Wing attachment to the fuselage uses a setup that has a "hook" in the front and two nylon screws in the back. The hook is make of 1/16" light ply with 1/8" balsa filler in between, and is glued to the dihedral brace. I also added a thin ply strip to the top of F2 that centers the hook and prevents it from sliding sideways: The wing is braced to the top of F3 by two #6-32 nylon screws. The crews go directly into the 1/8" triangle gussets without any blind nuts. There was no space for the blind nuts and the hole in the gusset is threaded and reinforced with CA to preserve the threads:

Aileron servo

Image
Aileron servos are Hitec HS-40. They will be permanently glued to a tray on the wing and linked to the ailerons: The servo will be glued to the tray after the bottom covering is in place and before the top wing covering is attached.

Ailerons

Image
I had a few ideas for hinging including thread-stitched hinges, covering film, etc. Since I will be using Esaki Japanese tissue I decided to use traditional nylon hinges instead of follow the building article with iron-on film and film hinges. The tissue and dope method is one of my favorite ways of covering, it is both old-school and helps bring out the beauty of balsa built models rather then covering them with opaque film. Covering side-bar: Here's a test square I made with Esaki tissue from Peck Polymers that I purchased for the Velie Monocoupe since they have the blue and orange colors I wanted. The square is 120x100mm and the net weight of the cover is about 1gr: Back to aileron hinges. The new LE and TE for the ailerons was not thick enough for the hinges so I built out the area with two 1/16" balsa strips that will hold the hinge between them. The first layer is glued 1/16" below the top so that the second sheet is flush with the top of the rib: I marked the hing ...